- Home
- Hifi Home
-
Speakers Technical
-
Car Audio
-
Auto Care
Car interior cosmetics
- Car interior cleaners
- Protection and impregnation of internal textile parts
- Protection and impregnation of internal plastic parts
- Car leather care products
- Odor eliminators and air conditioning cleaners
- Paintbrushes and interior brushes
- Applicators and wipes for internal use
- Set for a clean and fragrant car interior
-
Pro Audio
-
Marine Audio
-
Sport & Free time
- Specials Offers
- Brands
Visaton Basic 100 floorstanding speakers from Hobby Hifi 2/2015
Kit without housing price per speaker
A good floor-standing loudspeaker for around 100 EUR each: that was the aim of the Basic 100. It contains Visaton loudspeaker chassis: a Visaton DTW70 tweeter and a W100S woofer.
You might also like
Visaton Basic 100 floorstanding speakers from Hobby Hifi 2/2015
Kit without housing price per speaker
A good floor-standing loudspeaker for around 100 EUR each: that was the aim of the Basic 100. It contains Visaton loudspeaker chassis: a Visaton DTW70 tweeter and a W100S woofer.
A 2-way crossover is used, which consists of a 2nd order high-pass filter (12 dB/octave) and a 2nd order low-pass filter (12 dB/octave). To further flatten the frequency response, an absorption circuit is used parallel to the tweeter and woofer.
The frequency response of the loudspeaker is quite flat between 70 and 13000 Hz, apart from a slight dip at 2 kHz. The decay spectrum (waterfall spectrum) shows a delayed decay behavior in the middle. The non-linear distortions remain almost consistently below 1% at 90 dB sound pressure (1m) above 120 Hz. These are good measurements for the price of the speaker.
.
Technical data:
- Impedance: 4 Ohm
- Sound pressure level (2.83V/1m): 84 dB
- Dimensions (HxWxD): 788 x 150 x 210 mm
- Frequency range (-8dB): 30 - 26000 Hz
- Crossover frequency(s): 4000 Hz
- Principle: bass reflex box
.
Highlights
- Visaton tweeter dome DTW 72, 8 Ohm
- Visaton woofer W100 S, 4 Ohm
- PE foam sealing strip, 5x2
- Insulating material Sonofil 100 x 35 cm for 20 liters
- Pole terminals PK31, one pair, gold-plated, red+black
- 2m speaker cable 2x1.5 mm2, transparent
- Pan screws 4x20 black, Phillips, 4 pieces
- Visaton countersunk screws 3.5x25, 8 pieces
- Construction plan for the kit the crossover components (right), to be assembled on a wooden board.
- 2x rough electrolytic capacitor, 10 μF/100 Vdc
- Elko smooth, 1 μF / 70 Vdc
- Elko smooth, 3.3 μF / 70 Vdc
- 0.5 mm air coil, 0.1 mH/0.38 0hm
- 0.5 mm air coil, 0.22 mH/0.59 0hm
- 0.5 mm air coil, 2.2 mH/2.50 0hm
- 1.0 mm air coil, 0.68 mH/0.47 Ohm
- Ceramic resistor 2.2 Ohm/5 Watt
- Ceramic resistor 3.3 Ohm/5 Watt
- 2x ceramic resistor 6.8 Ohm/5 Watt
Basic 100
2 Items
You might also like
16 other products in the same category:
DIY component packs
Audaphon Sculptor floorstanding loudspeakers Kit with high-end crossover
0 review
DIY component packs
Tang Band Power Trio 2145 floorstanding loudspeaker from K+T magazine 3/2019
0 review
DIY component packs
Scan Speak CT 304 floorstanding loudspeaker Kit with high-end crossover
0 review
DIY component packs
Monacor Long Tall Sally floorstanding loudspeaker kit with high-end crossover
0 review
DIY component packs
Audaphon Angara 2 floorstanding loudspeakers Kit with high-end crossover
0 review
DIY component packs
Celestion HiFi-PA 2x8/2 floorstanding speakers Kit with high-end crossover
0 review
-
Products from the same brand
DIY component packsVisaton Aluminata 130/4 KE floorstanding loudspeaker from Hobby Hifi 3/2016
0 review
DIY component packsVisaton Aluminata 130/4 KE floorstanding loudspeaker Kit with high-end crossover
0 review