Arylic Up2Stream amp 2.0 V4 WiFi and Bluetooth 5.0 Stereo Amplifier Board

Product description

Does your next project require a high-end amplifier, Bluetooth 5.0 connection, Wi-Fi streaming, multi-room use or maybe even all of them? Then boy, do I have news for you! The brand new Up2Stream Amp V3 is here to satisfy all your needs!

.

Highlights

Wireless streamer and amplifier in one

Bluetooth 5.0 and Wi-Fi streaming using the free app

Supports multi-room use.

.

Product details

Arylic Up2Stream amp 2.0 V4 WiFi and Bluetooth 5.0 Stereo Amplifier Board

Does your next project require a high-end amplifier, Bluetooth 5.0 connection, Wi-Fi streaming, multi-room use, or maybe even all of them? Boy, do I have good news for you! The brand new Up2Stream Amp is here to satisfy all your needs!

This amplifier can stream music off of any reputable streaming service using its free Android and iOS app; Wi-Fi, Bluetooth 5.0, DLNA, AirPlay, Spotify, Deezer, Tidal, Qobuz, iheartRadio, Napster, internet radio you name it. Not only is the app very useful for uncompressed music streaming, but it also allows you to change the name of every Arylic product on your network and to set up a multi-room sound system.

The amplifier uses a powerful low distortion class D amplifier chip outputting up to 50 Watts per channel into 4 Ohms. It features every connection one may need and even has a USB port that can either be used as a USB DAC or for USB storage of your favorite tracks.

To control the amplifier, the free app, a PC or the optional remote control can be used.

.

Difference between V3 and V4

The version 4 has received a hardware revision, which supports more features with ACPWorkbench Audio effect tools. Like adjust L/R balance, L/R EQ settings etc. And ads more DIY pins like I2S and DAC output, so you have more options to connect DIY modules.

-

What’s in the box?

Up2Stream 2.0 Amp

4-pin analog connector

4-pin cable

Screw Driver

Wi-Fi Antenna

User manual

.

Warning:Up2Stream Amp 2.0 V4 must use 12V-26 VDC input, higher voltage power supply may damage the board.

.

Specifications

Article number

Up2Stream Amp 2.0

Rated power output (RMS)

2 x 50 watts at 4 ohms (21 V)

Bridged power output (RMS)-

Minimum load 4 Ohms

Signal-to-noise ratio (SNR) 91 dB

Distortion 0.03 % THD at 1 kHz, 50 Watts

Distortion bridged -

Efficiency -

Frequency response

20 - 20,000 Hz

Input impedance -

Input sensitivity -

Auto turn-on sensitivity -

DSP -

DAC micro-USB DAC

Maximum sampling rate up to 24bit, 192kHZ

Circuit Topology -

Amplifier classification Class D

Speaker output channels Left and Right

Subwoofer output channel -

Analog in/out 2/1

Optical S/PDIF in/out -

Coaxial in/out -

RCA in/out -

AUX in/out -

Bus in/out -

XLR in/out -

USB

USB power, USB DAC, USB storage

Memory card slot -

Network connection

 Single 10/100M RJ45

Headphone jack -

Subwoofer pre-out -

Bluetooth Bluetooth 5.0

NFC -

Wi-Fi  IEEE802.11 b/g/n 2.4G

Banana plug compatible -

Remote control IR remote compatible

App control Free Android and iOS app

Auto turn-on -

Accepted file formats FLAC, MP3, AAC, AAC+, ALAC, APE, WAVE

Equalizer (EQ) adjustment in-app equalizer adjustment

Equalizer (EQ) profiles -

Multi zone/room App supports Multi-Room playback

Crossover frequency adjustment -

Bridge mode -

Power requirements DC 12V-26V 4A

Power inlet connector 5.5 mm x 2.1 mm DC plug

Stand-by power consumption-

Dimensions (D x W x H) 80 x 100 x 20 mm